How to design a commercial kitchen ventilation system
commercial kitchen ventilation system
11/1/20267 min read
Start with the cooking equipment, not the fan. A commercial kitchen ventilation blueprint should begin with the appliance schedule, calculate extract airflow rather than estimate it from canopy length, and balance extraction with make-up air. Build the system requirements into the design from the outset.
Effective ventilation involves more than removing heat and smoke. Hood capture, airflow, fire safety, and cleanable ductwork must work together in the finished kitchen.
This guide explains how to plan the system, select an exhaust fan to suit the design, and account for grease filtration, odour control, fire safety, and commissioning. It highlights the decisions that shape layout and airflow, helping you develop a practical ventilation plan from the equipment schedule.
Key Takeaways
Map the cooking equipment first, then plan hood capture and calculate extract airflow instead of sizing from canopy length alone.
Select an extractor fan to suit the required airflow and duct system, while balancing exhaust with make-up air.
Plan fire protection and commissioning alongside the ventilation layout so the system can be checked for safe, effective operation.
Choose grease filtration and odour-control measures that fit the cooking process, and design ductwork for practical cleaning access.
Table of Contents
How do you design a commercial kitchen ventilation system?
Start with the appliance schedule and cooking equipment. Then map capture, extract, and make-up air. Calculate extract volume using DW/172, rather than canopy length alone. Use the commercial kitchen ventilation blueprint to coordinate these decisions before installation.
Plan canopy or ventilated-ceiling capture
Position the canopy or ventilated ceiling over the appliance schedule, then check capture at each cooking zone. Extend a canopy at least 6 inches beyond cooking equipment. For a four-sided island hood, exhaust rates should be calculated for the specific design. Guidance also lists 250–350 CFM per linear foot for UL-rated canopy hoods, compared with 300–400 CFM per linear foot for non-rated hoods.
Set out blueprint contents
Include the appliance schedule, hood or ceiling capture, and calculated extract volume. Add make-up-air routes, duct runs, fan position, and discharge point. Use DW/144 for extract-duct construction and TR/19 for cleanability. Mark access panels along the duct route so cleaning and maintenance remain practical. Record these details in the commercial kitchen ventilation blueprint to coordinate equipment positions and reduce disruptive layout changes.
Design make-up air and pressure balance
Plan make-up air at 60 to 85% of kitchen exhaust airflow, then balance supply against extract. Keep kitchen-area negative pressure from exceeding 0.02 inches water column (4.98 PA). Limit short-circuit make-up air to no more than 15% of exhaust airflow. Position supply outlets so incoming air supports hood capture instead of pushing cooking fumes away from the canopy.
Address design failures, health risks, and noise
Review capture, airflow balance, and fan noise together rather than treating them as separate design issues. A canopy sized by length alone may not meet the extract demand created by the appliances beneath it. The National Environment Agency says individual cooking-table extraction hoods should be operational and properly maintained to remove combustion-generated pollutants at source. Check fan and duct routing for avoidable turbulence, which can increase noise without improving capture.
ASTM F -1704 is identified in the course as a standard test method for commercial kitchen ventilation-system performance, providing a reference for evaluating system design.
Fan selection
Choose the exhaust fan after establishing the required airflow and duct route. In Singapore, the Singapore Food Agency says food-processing areas need adequate extractor fans for ventilation.
Set the required fan duty from the calculated extract demand. Use the design airflow as the target, not canopy measurements or the fan’s maximum rating alone. The fan must move air through the complete planned system, including the hood, filters, ductwork, bends, and discharge point.
Match fan performance to system resistance. Long duct runs, multiple bends, and restrictive components increase resistance and affect delivered airflow. Compare the fan’s performance at the system’s operating point, so selection reflects the installed layout rather than an isolated catalogue figure.
Choose a fan arrangement that suits the kitchen and discharge route. Consider installation space, maintenance access, and how exhaust leaves the building. Coordinate the fan position with duct access panels and the route planned for cleaning.
Review noise and vibration during fan selection. Fan location, mounting, duct transitions, and airflow all affect sound transmission. Where the layout allows, avoid abrupt changes in duct direction, which can increase resistance and disturb airflow. Consider nearby food preparation and service areas when positioning equipment.
Coordinate the fan with make-up air and operating controls. It should work as part of the full ventilation system, not as a standalone component. Compare fan operation with the planned supply-air arrangement, then identify how the system will be tested under normal cooking conditions.
Record the selected fan’s duty, location, duct connection, and commissioning checks on the project drawings. This gives installers a clear basis for fitting the equipment and testing whether the completed system delivers its intended extract airflow.


Fire safety and commissioning
For Singapore project reviews, prepare coordinated drawings that show the hood, extract ducts, fan, discharge, and fire-protection arrangement. Include the appliance schedule and commissioning records so the proposed layout and completed system can be reviewed together.
Set hood and duct cleaning frequency according to cooking duty and grease accumulation. Inspect filters and accessible duct sections, and clean deposits before they build up.
Keep exhaust ductwork at least 18 inches from combustible surfaces. Show this clearance on the layout, especially where ducts pass near ceilings or structural elements. NFPA 96 covers ventilation control and fire protection for commercial cooking operations; treat it as a technical reference, not a substitute for Singapore project requirements.
Coordinate the hood with its fire-extinguishing arrangement. NFPA 17A addresses wet-chemical fire-extinguishing systems. Confirm the system’s position relative to the cooking appliances, hood, and filters, then document how the components interact during commissioning.
Include hood filters and duct access points in the cleaning plan. Cooking duty and visible grease deposits help determine cleaning frequency. Keep access panels clear, record inspection findings, and remove grease before deposits obstruct airflow or add fuel within the duct route.
Test the installed system under normal operating conditions. Check that each hood and exhaust fan operates, airflow reaches the intended capture points, and make-up air does not disrupt capture. The National Environment Agency (NEA) says individual cooking-table extraction hoods should be operational and properly maintained to remove combustion-generated pollutants at source.
Record commissioning results and outstanding adjustments. Check hood-filter temperatures remain below 200°F, then document the readings and any corrective work. Use the records to track system performance and guide later inspections, cleaning, and maintenance.
Grease filtration and odour control
Match grease filtration to the cooking equipment and its duty. Identify appliances that produce grease-laden vapour, then place filters within the capture path. Filters collect grease before exhaust enters the ductwork. Choose an arrangement that can be accessed, removed, and cleaned without obstructing routine kitchen operations.
Plan filter access and maintenance alongside the hood layout. Filters that are difficult to remove are harder to inspect and clean. Keep access clear and include filter checks in the kitchen’s cleaning routine. Visible grease build-up, for example, signals that a filter needs attention before deposits travel further into the exhaust route.
Address odour at the design stage. Identify the cooking processes and exhaust discharge point, then consider how filtration and the exhaust path work together. Odour-control equipment should suit the exhaust stream and fit the planned duct layout. It does not replace effective hood capture and grease filtration.
Coordinate gas interlocking with the ventilation controls. IGEM/UP/19 and BS 6173 are standards relevant to commercial kitchen gas interlocking. Show the interlocking arrangement on the system drawings, including how the ventilation and gas controls interact. Keep the design coordinated with the cooking equipment and planned operating sequence.
Document the locations of filtration, odour-control equipment, and control systems on the kitchen plan. Mark filter and duct-cleaning access, as well as the gas-interlocking arrangement. During commissioning, confirm that components are installed as drawn and controls operate in the intended sequence. Clear drawings also help kitchen staff identify points for routine inspection.
Use these decisions to coordinate the hood and exhaust layout before installation. Discuss your commercial kitchen hood layout as part of planning the system.
Air Flow M&E Pte: Commercial Kitchen Hood Installation
Air Flow M&E Pte Ltd provides Commercial Kitchen Hood Installation for commercial kitchens planning a new hood or updating an existing setup. Choose this service when the hood layout needs to align with the cooking equipment and exhaust route. A coordinated installation connects the capture point with the wider ventilation design.
For wider project requirements, Air Flow M&E Pte Ltd also provides Commercial Exhaust Motor Installation and custom-fitted ductwork. These services address key system components, from moving extracted air to routing it through the kitchen, and suit projects involving more than the hood alone.
Contact Air Flow M&E Pte Ltd to discuss your commercial kitchen hood installation.
Turn your ventilation plan into the next project step
A well-developed commercial kitchen ventilation blueprint gives the project team a clear basis for coordinating equipment, installation, and system changes. Before work begins, bring together the kitchen layout and intended cooking equipment. Use these to define the project scope and identify where specialist installation or alterations are needed.
Air Flow M&E Pte Ltd provides Commercial Kitchen Exhaust System Addition & Alteration (A&A) Services, Commercial Kitchen Hood Installation, and Commercial Exhaust Motor Installation. These services support new kitchen setups and changes to existing commercial exhaust systems. The right starting point depends on the work required by your layout.
Ready to move from planning to implementation? Contact Air Flow M&E Pte Ltd to discuss your commercial kitchen ventilation project. A clear plan is a practical first step toward a kitchen designed around its equipment and day-to-day operation.
Frequently Asked Questions
How is energy efficiency built into the design?
Build energy efficiency into the system by matching airflow and fan operation to kitchen demand. Coordinate hood capture, duct routing, and make-up air as one system rather than designing around excess capacity. For example, a kitchen with separate cooking and preparation zones can plan controls around the active cooking area, avoiding unnecessary extraction when cooking equipment is idle.
What are the ventilation requirements for commercial kitchens in Singapore?
Food-processing areas need adequate extractor fans, according to the Singapore Food Agency. Translate that requirement into a kitchen-specific plan by listing each appliance, cooking process, and operating pattern. A bakery line, wok station, and dishwasher create different ventilation demands. The design should reflect the kitchen’s actual use and provide extract and replacement air suited to its planned operation.
What are the recommended hood types and duct layouts for different cooking equipment?
Choose hood geometry according to equipment placement and plume capture. A wall-backed line of fryers or ranges can use a canopy over the cooking run, while island equipment needs capture from its exposed sides. Consider the different cooking duties before grouping appliances beneath one hood. Route ducts directly where practical, while preserving access for inspection and cleaning.
What are the fire-safety requirements for kitchen exhaust ducts, grease filters and fire suppression in Singapore?
Coordinate grease filters, exhaust ductwork, and fire suppression as one system. Show how filters can be removed for cleaning, how duct sections remain accessible, and how suppression protects the cooking area beneath the hood. Document the fire-safety design basis in the project drawings. Do not assume that an international standard alone establishes Singapore compliance; distinguish technical references from the requirements that apply to the project.
Airflow M&E Ptd Ltd
BCA-registered Construction Company with measured airflow performance across Singapore.
Navigation
Home
Service
Price
Air-Clean 4000
Contact
Blog
Service Desk
+65 8222 3444
+65 9863 8222
+65 9102 8222
Office operating daily 09:00 - 18:00 SGT
#08-06, 65 Sims Ave, Singapore 387418
© 2026 Airflow-M&E Ptd Ltd
Efficient Air-Flow Ventilation throughout commercial spaces


